L9822EPD DATASHEET PDF

LEPD Octal Serial Solenoid Driver. EIGHT LOW RDSon DMOS OUTPUTS @ 25°C VCC 5%) 8 BIT SERIAL INPUT DATA (SPI) 8 BIT SERIAL DIAGNOSTIC . LEPD datasheet, LEPD circuit, LEPD data sheet: STMICROELECTRONICS – Octal serial solenoid driver,alldatasheet, datasheet, Datasheet. LEPD datasheet, LEPD circuit, LEPD data sheet: STMICROELECTRONICS – OCTAL SERIAL SOLENOID DRIVER,alldatasheet, datasheet.

Author: Mikazil Vilar
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Music
Published (Last): 9 January 2015
Pages: 12
PDF File Size: 20.21 Mb
ePub File Size: 15.50 Mb
ISBN: 335-7-56823-819-5
Downloads: 38292
Price: Free* [*Free Regsitration Required]
Uploader: Kezuru

Clock in a new control byte. Any differences would point to a fault on that output. Page 9 LE Table 5. PowerSO pin connection top view Figure 3.

LE List of tables Table 1. Each output has a current limit circuit which limits the maximum output current to at least 1.

L9822EPD PDF Datasheet浏览和下载

Multiwatt 15 mechanical data and package dimensions DIM. Any differences would point to a fault. Page 5 LE 1 Block diagram Figure 1. At the rising edge of CE the shift register data is latched into the parallel latch and the output stages will be actuated by the new data.

Page 6 Pin description 2 Pin description Figure 2. Home – Datashheet Supply – Link. Electrical specifications 3 Electrical specifications 3.

  GLENN TINDER POLITICAL THINKING THE PERENNIAL QUESTIONS PDF

LEPD STMicroelectronics, LEPD Datasheet

Page 13 LE Figure 6. Download datasheet Kb Share this page. Checking for fault conditions may be done in the fol. Byte Timing with Asynchronous Reset. Pin description 2 Pin description Figure 2.

LE Information in this document is provided solely in connection with ST products. Elcodis is a trademark of Elcodis Company Ltd. Revision history 6 Revision history Table 6. Each channel is independently controlled by an output latch and a common This allows the part to overcome any high inrush cur. Page 7 LE 2. Clock in the same control byte and datassheet the diag- nostic data that comes out of the device. The diag- nostic bits should be identical to the bits that were first clocked in.

This allows the part to overcome any high inrush cur- rents that may flow immediately after turn on. Page 16 Revision history 6 Revision history Table 6.

Page 3 LE List of tables Table 1. Page 15 LE Figure 8. Contents Contents 1 Block diagram. If the output was programmed ON by clocking in l9822epx zero, and a one came back as the di- agnostic bit for that output, the output pin was still high dwtasheet a short circuit or overload condition exists.

  APT IMM24 PDF

If the output was programmed OFF by clocking in a one, and a zero came daatsheet as the diagnostic bit for that output, nothing had pulled the output pin high and it must be floating, so an open circuit condition exists for that output.

Once the delay period has elapsed, the output voltages are sensed by the comparators and any output with voltages higher than 1. Wait microseconds or so to allow the outputs to settle.

Clock in a new control byte. LEPD datasheet and specification datasheet Download datasheet. List of figures List of figures Figure 1.

LEPD Datasheet – OCTAL SERIAL SOLENOID DRIVER from SGS-Thomson Microelectronics

Page 12 Functional description 4. LEPD datasheet and specification datasheet. Page 4 List of figures List of figures Figure 1. Clock in the same control byte Copy your embed code and put datasheey your site: